ESU LLP manufacture & sell LED transilluminators in Japan & abroad.
ＭＡＮＵＡＬ （RED LED LIGHT MK-03TL Plus)
Side Transilluminator
Red LED Light MK-03TL Plus, Transilluminator Vein Finder
User's Manual
You are kindly requested to use the Red LED Light MK-03TL Plus properly as explained below.
Specifications
"Device section"
Power Supply：2xAA alkaline battery
Output Light：Red LED light
"Materials"
Lighting unit(twin light)：Al(top case)+ABS(bottom base)
Connecting Plate：translucent polycarbonate resin
Power unit：PC/ABS(flame retardant)
"Weight"
Lighting unit(twin light)：10gr including a connecting plate
Power unit：60gr(excluding 2xAA battery）
"Dimension"
Lighting unit(twin light)：25(L)x13(W)x13.4(H)mm/ea.,/connecting plate：41(L)x10(W)x3(D)
Power unit：84(L)x53(W)x25(H)mm
Cord length：about 66cm/2.4Фmm
Disinfection：ethanol dipped sterile cotton
How to operate the device
１．Procedure
① Interject the vein that you want to find bewteen the twin lights that are placed in close contact
with the patient's skin. The twin lights are positioned at a proper distance apart to enable best vein
image
② Turn on the power to irradiate the vein area & move the twin lights freely, searching for a proper
vein. (To secure optimal skin to device contact , fine angle adjustment of the twin lights is made
possible by manually rotating the twin lightsaround the screw axis. When the screws become loose
, be sure to tighten them, bt not too strongly.The translucent connecting plate can be detached by
.Do not irradiate one area for a long time in order to avoid the tissue burn
④ please be sure that the same spot on the skin is not irradiated for longer than 5 minutes.
Forbidden Actions
★ Do not stare at the light source while its power is turned ON
★ Do not irradiate other person's eyes.
★ Do not spill liquid over either the lighting units &/orpower unit.
★ Do not either disassemble or modify the device.
★ Do not either bend or twist the cord near the lighting or power units.
Warranty
The device is warranted for one year from the date of your purchase.
For warranty, the proof of your purchase date and serial number are required.
patents approved
BACK
User's Manual
You are kindly requested to use the Red LED Light MK-03TL Plus properly as explained below.
Specifications
"Device section"
Power Supply：2xAA alkaline battery
Output Light：Red LED light
"Materials"
Lighting unit(twin light)：Al(top case)+ABS(bottom base)
Connecting Plate：translucent polycarbonate resin
Power unit：PC/ABS(flame retardant)
"Weight"
Lighting unit(twin light)：10gr including a connecting plate
Power unit：60gr(excluding 2xAA battery）
"Dimension"
Lighting unit(twin light)：25(L)x13(W)x13.4(H)mm/ea.,/connecting plate：41(L)x10(W)x3(D)
Power unit：84(L)x53(W)x25(H)mm
Cord length：about 66cm/2.4Фmm
Disinfection：ethanol dipped sterile cotton
How to operate the device
１．Procedure
① Interject the vein that you want to find bewteen the twin lights that are placed in close contact
with the patient's skin. The twin lights are positioned at a proper distance apart to enable best vein
image
② Turn on the power to irradiate the vein area & move the twin lights freely, searching for a proper
vein. (To secure optimal skin to device contact , fine angle adjustment of the twin lights is made
possible by manually rotating the twin lightsaround the screw axis. When the screws become loose
, be sure to tighten them, bt not too strongly.The translucent connecting plate can be detached by
unscrewing the two screws, then light units can be placed onto any skin
area as needed
③ Once the blood draw is established, be sure to turn off the switch..Do not irradiate one area for a long time in order to avoid the tissue burn
④ please be sure that the same spot on the skin is not irradiated for longer than 5 minutes.
Forbidden Actions
★ Do not stare at the light source while its power is turned ON
★ Do not irradiate other person's eyes.
★ Do not spill liquid over either the lighting units &/orpower unit.
★ Do not either disassemble or modify the device.
★ Do not either bend or twist the cord near the lighting or power units.
Warranty
The device is warranted for one year from the date of your purchase.
For warranty, the proof of your purchase date and serial number are required.
| name | LED transilluminator |
| serial # | indicated inside the power unit |
| FDA | registration # 3006737183 |
| operator # 9097725 | |
| listing # E579683 |
| manufacturer & distributor | |
| name |
esu llp |
| address |
2-2-7 Akanedai Aoba Yokohama JAPAN 227-0066 |
| phone |
+81 45 512 9560 |
| fax |
+81 50 3156 7835 |
| URL |
http://redlight.jp |
patents approved
BACK